If you are planning to study Mechatronics Engineering at Baze University located in Federal Capital Territory (FCT), it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Baze University was established in 2011 as a private university in Abuja to provide quality higher education with emphasis on entrepreneurship, leadership, and innovation. This page explains everything you need to know to increase your chances of gaining admission into Baze University.
Does Baze University offer Mechatronics Engineering?
No, Baze University does not offer Mechatronics Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Baze University below to check if the Mechatronics Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechatronics Engineering When Accredited in Baze University
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechatronics Engineering department under Faculty of Engineering / Technology.
any other Science subject.
Baze University Cut-Off Mark for Mechatronics Engineering
The general UTME cut-off mark is 180, but due to the variation of Mechatronics Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Baze University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Baze University Science Courses with their Requirements
1. Human Physiology
To study this course, candidates aspiring to gain admission into Human Physiology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
2. Surveying and Geoinformatics
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
3. Telecommunication Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Telecommunication Engineering department.
any two (2) other relevant subjects.
4. Petroleum Engineering
To study this course, the minimum requirement for applicants seeking admission to the Petroleum Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
5. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
6. Physics
To study this course, the minimum requirement for applicants seeking admission to the Physics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Chemistry, Mathematics and
any other Science subject from
Biology / Agricultural Science.
7. Mechanical Engineering
To study this course, candidates seeking admission into the Mechanical Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant Science subjects.
Nigerian Universities Offering Mechatronics Engineering Course