If you are planning to study Prosthesis and Orthopaedic Technology at Baze University located in Federal Capital Territory (FCT), it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Baze University.
Does Baze University offer Prosthesis and Orthopaedic Technology?
No, Baze University does not offer Prosthesis and Orthopaedic Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Baze University below to check if the Prosthesis and Orthopaedic Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Prosthesis and Orthopaedic Technology When Accredited in Baze University
O’Level Requirements
To study this course, candidates aspiring to gain admission into Prosthesis and Orthopaedic Technology department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Baze University Cut-Off Mark for Prosthesis and Orthopaedic Technology
The general UTME cut-off mark is 180, but due to the variation of Prosthesis and Orthopaedic Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Baze University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Baze University Science Courses with their Requirements
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Urban and Regional Planning (URP) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Mechanical Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Mechanical Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant Science subjects.
Architecture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Building
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Chemistry
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Chemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates seeking admission into the Surveying and Geoinformatics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Biology
SSCE Requirements
To study this course, candidates seeking admission into the Biology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Mathematics / Physics and
any one other relevant subject.
Nigerian Tertiary Institutions Offering Prosthesis and Orthopaedic Technology Course