If you are planning to study Software Engineering at Baze University located in Federal Capital Territory (FCT), it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Baze University was established in 2011 as a private university in Abuja to provide quality higher education with emphasis on entrepreneurship, leadership, and innovation. This page explains everything you need to know to increase your chances of gaining admission into Baze University.
Does Baze University offer Software Engineering?
No, Baze University does not offer Software Engineering under its Faculty of Data and Decision Sciences. However, since our course list is updated regularly, you can visit the courses available at Baze University below to check if the Software Engineering course under the Faculty of Data and Decision Sciences has been updated.
Admission Requirements for Software Engineering When Accredited in Baze University
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Software Engineering department under Faculty of Data and Decision Sciences.
two (2) other Science subjects.
JAMB Subject Combination
Biology, Chemistry, Agric Science, Economics and Geography.
Baze University Cut-Off Mark for Software Engineering
The general UTME cut-off mark is 180, but due to the variation of Software Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Baze University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Baze University Science Courses with their Requirements
1. Computer Science (CS)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Science (CS) department.
any two (2) other Science subjects.
2. Surveying and Geoinformatics
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
3. Electrical / Electronics Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Electrical / Electronics Engineering department.
any other Science subject.
4. Telecommunication Engineering
To study this course, candidates aspiring to gain admission into Telecommunication Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subjects.
5. Petroleum Engineering
To study this course, candidates aspiring to gain admission into Petroleum Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
6. Mechanical Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Engineering department.
any two (2) other relevant Science subjects.
7. Quantity Surveying (QS)
To study this course, candidates aspiring to gain admission into Quantity Surveying (QS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
Nigerian Universities Offering Software Engineering Course