If you are planning to study Wood Production Engineering at Baze University located in Federal Capital Territory (FCT), it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Baze University was established in 2011 as a private university in Abuja to provide quality higher education with emphasis on entrepreneurship, leadership, and innovation. This page explains everything you need to know to increase your chances of gaining admission into Baze University.
Does Baze University offer Wood Production Engineering?
No, Baze University does not offer Wood Production Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Baze University below to check if the Wood Production Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Wood Production Engineering When Accredited in Baze University
O’Level Requirements
To study this course, candidates seeking admission into the Wood Production Engineering department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Baze University Cut-Off Mark for Wood Production Engineering
The general UTME cut-off mark is 180, but due to the variation of Wood Production Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Baze University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Baze University Science Courses with their Requirements
1. Quantity Surveying (QS)
To study this course, candidates seeking admission into the Quantity Surveying (QS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
2. Building
To study this course, the minimum requirement for applicants seeking admission to the Building department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
3. Physics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Physics department.
Chemistry, Mathematics and
any other Science subject from
Biology / Agricultural Science.
4. Architecture
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
5. Urban and Regional Planning (URP)
To study this course, candidates seeking admission into the Urban and Regional Planning (URP) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
6. Civil Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Civil Engineering department.
7. Mechanical Engineering
To study this course, candidates seeking admission into the Mechanical Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant Science subjects.
Nigerian Tertiary Institutions Offering Wood Production Engineering Course