If you are planning to study Dental Technology at Bells University of Technology located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Bells University.
Does Bells University of Technology (BUT) offer Dental Technology?
No, Bells University of Technology does not offer Dental Technology under its Faculty of Health and Medical Sciences. However, since our course list is updated regularly, you can visit the courses available at Bells University of Technology (BUT) below to check if the Dental Technology course under the Faculty of Health and Medical Sciences has been updated.
Admission Requirements for Dental Technology When Accredited in Bells University of Technology (BUT)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Dental Technology department under Faculty of Health and Medical Sciences, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
JAMB Subject Combination
one (1) other Science subject.
Bells University Cut-Off Mark for Dental Technology
The general UTME cut-off mark is 230, but due to the variation of Dental Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Bells University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Bells University Science Courses with their Requirements
Biochemistry
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Biochemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Applied Mathematics with Statistics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Applied Mathematics with Statistics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
two (2) other Science subjects.
Communication Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Communication Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subjects.
Mechanical Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mechanical Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant Science subjects.
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Food Science and Technology (FT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Food Science and Technology (FT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Architecture
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Nigerian Tertiary Institutions Offering Dental Technology Course