If you are planning to study Industrial Mathematics at Bells University of Technology located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Bells University was established in 2005 as a private university of technology in Ogun State to advance science, engineering, and technological education in Nigeria. This page explains everything you need to know to increase your chances of gaining admission into Bells University.
Does Bells University of Technology (BUT) offer Industrial Mathematics?
No, Bells University of Technology does not offer Industrial Mathematics under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Bells University of Technology (BUT) below to check if the Industrial Mathematics course under the Faculty of Science has been updated.
Admission Requirements for Industrial Mathematics When Accredited in Bells University of Technology (BUT)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Industrial Mathematics department under Faculty of Science.
two (2) other Science subjects.
JAMB Subject Combination
any two (2) other subjects from
Physics, Chemistry, Economics,
Biology and Agricultural Science.
Bells University Cut-Off Mark for Industrial Mathematics
The general UTME cut-off mark is 180, but due to the variation of Industrial Mathematics cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Bells University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Bells University Science Courses with their Requirements
1. Nutrition and Dietetics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Nutrition and Dietetics department.
Biology/Agricultural Science.
2. Building Technology (BT)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
3. Surveying and Geoinformatics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
4. Biotechnology
To study this course, candidates aspiring to gain admission into Biotechnology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
5. Biochemistry
To study this course, the minimum requirement for applicants seeking admission to the Biochemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
6. Food Science and Technology (FT)
To study this course, candidates aspiring to gain admission into Food Science and Technology (FT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
7. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Nigerian Universities Offering Industrial Mathematics Course