If you are planning to study Industrial Physics With Applied Geophysics at Bells University of Technology located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Bells University.
Does Bells University of Technology (BUT) offer Industrial Physics With Applied Geophysics?
No, Bells University of Technology does not offer Industrial Physics With Applied Geophysics under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Bells University of Technology (BUT) below to check if the Industrial Physics With Applied Geophysics course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Industrial Physics With Applied Geophysics When Accredited in Bells University of Technology (BUT)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Industrial Physics With Applied Geophysics department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Bells University Cut-Off Mark for Industrial Physics With Applied Geophysics
The general UTME cut-off mark is 180, but due to the variation of Industrial Physics With Applied Geophysics cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Bells University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Bells University Science Courses with their Requirements
1. Food Science and Technology (FT)
To study this course, candidates aspiring to gain admission into Food Science and Technology (FT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
2. Civil Engineering
To study this course, candidates aspiring to gain admission into Civil Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
3. Architecture
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
4. Surveying and Geoinformatics
To study this course, candidates seeking admission into the Surveying and Geoinformatics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
5. Biomedical Engineering
To study this course, candidates aspiring to gain admission into Biomedical Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
6. Electrical / Electronics Engineering
To study this course, candidates seeking admission into the Electrical / Electronics Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
7. Information Technology
To study this course, candidates aspiring to gain admission into Information Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subjects.
Nigerian Tertiary Institutions Offering Industrial Physics With Applied Geophysics Course