If you are planning to study Mechanical Metalwork Technology Education at Bells University of Technology located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Bells University.
Does Bells University of Technology (BUT) offer Mechanical Metalwork Technology Education?
No, Bells University of Technology does not offer Mechanical Metalwork Technology Education under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Bells University of Technology (BUT) below to check if the Mechanical Metalwork Technology Education course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechanical Metalwork Technology Education When Accredited in Bells University of Technology (BUT)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Metalwork Technology Education department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
one (1) of Biology /Agricultural Science; Physics, or Chemistry and
two (2) from General Science/IntegratedScience, Technical Drawing/Fine Art, Health Science Food and Nutrition,
Geography, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
JAMB Subject Combination
any other relevant subject.
Bells University Cut-Off Mark for Mechanical Metalwork Technology Education
The general UTME cut-off mark is 180, but due to the variation of Mechanical Metalwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Bells University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Bells University Science Courses with their Requirements
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Urban and Regional Planning (URP) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Food Technology
SSCE Requirements
To study this course, candidates seeking admission into the Food Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science,
any two of the following:
Geography, Food and Nutrition, Economics, Technical Drawing, Physics, Chemistry, Nigerian Language and Home Economics.
At least a pass in Chemistry is required.
Food Science and Technology (FT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Food Science and Technology (FT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Mechatronics Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Mechatronics Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Architecture
SSCE Requirements
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Information Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Information Technology department.
any two (2) other relevant subjects.
Food Science with Business
SSCE Requirements
To study this course, candidates aspiring to gain admission into Food Science with Business department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science,
Physics, Basic Catering and Food Services, Bakery and Confectionaries, Hotel & Catering Crafty course (Cookery), Hotel & Catering Craft Course (Food /Drinks Services) and Basic Electricity.
Nigerian Tertiary Institutions Offering Mechanical Metalwork Technology Education Course