If you are planning to study Mechatronics and System Engineering at Bells University of Technology located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Bells University.
Does Bells University of Technology (BUT) offer Mechatronics and System Engineering?
No, Bells University of Technology does not offer Mechatronics and System Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Bells University of Technology (BUT) below to check if the Mechatronics and System Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechatronics and System Engineering When Accredited in Bells University of Technology (BUT)
O’Level Requirements
To study this course, candidates seeking admission into the Mechatronics and System Engineering department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Bells University Cut-Off Mark for Mechatronics and System Engineering
The general UTME cut-off mark is 180, but due to the variation of Mechatronics and System Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Bells University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Bells University Science Courses with their Requirements
Mechanical Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Engineering department.
any two (2) other relevant Science subjects.
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Architecture
SSCE Requirements
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Telecommunication Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Telecommunication Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subjects.
Microbiology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Microbiology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Food Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Food Technology department.
Biology / Agricultural Science,
any two of the following:
Geography, Food and Nutrition, Economics, Technical Drawing, Physics, Chemistry, Nigerian Language and Home Economics.
At least a pass in Chemistry is required.
Food Science with Business
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Food Science with Business department.
Biology/Agricultural Science,
Physics, Basic Catering and Food Services, Bakery and Confectionaries, Hotel & Catering Crafty course (Cookery), Hotel & Catering Craft Course (Food /Drinks Services) and Basic Electricity.
Nigerian Tertiary Institutions Offering Mechatronics and System Engineering Course