If you are planning to study Welding and Fabrication Technology at Benue State Polytechnic located in Benue State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into BENPOLY.
Does Benue State Polytechnic (BENPOLY) offer Welding and Fabrication Technology?
No, Benue State Polytechnic does not offer Welding and Fabrication Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Benue State Polytechnic (BENPOLY) below to check if the Welding and Fabrication Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Welding and Fabrication Technology When Accredited in Benue State Polytechnic (BENPOLY)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Welding and Fabrication Technology department under Faculty of Engineering / Technology.
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
JAMB Subject Combination
Physics/Technical Drawing or Chemistry.
BENPOLY Cut-Off Mark for Welding and Fabrication Technology
The general UTME cut-off mark is 180, but due to the variation of Welding and Fabrication Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from BENPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other BENPOLY Science Courses with their Requirements
Estate Management and Valuation
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Estate Management and Valuation department.
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Computer Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Computer Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Foundry Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Foundry Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
at least a pass in English Language,
any two relevant subjects from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Mechanical Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mechanical Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Printing Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Printing Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other subjects from:
Metal Work, Basic Electricity, Technical Drawing/Fine Art,
Book Keeping and Principles of Accounting, Economics/Commerce,
Nigerian Polytechnics Offering Welding and Fabrication Technology Course