If you are planning to study Mechanical Metalwork Technology Education at Bowen University located in Osun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Bowen University was established in 2001 by the Nigerian Baptist Convention as a private faith-based university focused on academic excellence, discipline, and moral upbringing. This page explains everything you need to know to increase your chances of gaining admission into Bowen University.
Does Bowen University (BU) offer Mechanical Metalwork Technology Education?
Wondering if Bowen University offers Mechanical Metalwork Technology Education in 2026? We cannot confirm this with certainty because Bowen University may make changes to its Faculty of Engineering / Technology courses. Our regularly updated course list provides the latest information on Bowen University Faculty of Engineering / Technology courses.
After Confirming Mechanical Metalwork Technology Education at Bowen University, Check the Admission Requirements
O’Level Requirements
To study this course, candidates aspiring to gain admission into Mechanical Metalwork Technology Education department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
one (1) of Biology /Agricultural Science; Physics, or Chemistry and
two (2) from General Science/IntegratedScience, Technical Drawing/Fine Art, Health Science Food and Nutrition,
Geography, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
JAMB Subject Combination
any other relevant subject.
Bowen University Mechanical Metalwork Technology Education Suggested Cut-Off Mark if Offered
The general UTME cut-off mark is 180, but due to the variation of Mechanical Metalwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Bowen University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Bowen University Science Courses with their Requirements
1. Surveying and Geoinformatics
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
2. Agriculture
To study this course, candidates aspiring to gain admission into Agriculture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science,
Mathematics / Physics, and
3. Education and Mathematics
To study this course, candidates seeking admission into the Education and Mathematics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
one (1) other Science subject, and
any other relevant subjects.
4. Architecture
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
5. Fisheries and Aquaculture
To study this course, candidates seeking admission into the Fisheries and Aquaculture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science,
Physics/Geography/Economics.
6. Biochemistry
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Biochemistry department.
7. Microbiology
To study this course, the minimum requirement for applicants seeking admission to the Microbiology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Nigerian Tertiary Institutions Offering Mechanical Metalwork Technology Education Course