If you are planning to study Mechatronics and System Engineering at Bowen University located in Osun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Bowen University was established in 2001 by the Nigerian Baptist Convention as a private faith-based university focused on academic excellence, discipline, and moral upbringing. This page explains everything you need to know to increase your chances of gaining admission into Bowen University.
Does Bowen University (BU) offer Mechatronics and System Engineering?
No, Bowen University does not offer Mechatronics and System Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Bowen University (BU) below to check if the Mechatronics and System Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechatronics and System Engineering When Accredited in Bowen University (BU)
O’Level Requirements
To study this course, candidates seeking admission into the Mechatronics and System Engineering department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Bowen University Cut-Off Mark for Mechatronics and System Engineering
The general UTME cut-off mark is 180, but due to the variation of Mechatronics and System Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Bowen University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Bowen University Science Courses with their Requirements
1. Electrical / Electronics Engineering
To study this course, candidates aspiring to gain admission into Electrical / Electronics Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
2. Forestry and Environmental Management
To study this course, candidates aspiring to gain admission into Forestry and Environmental Management department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
one of Physics, Economics, Further Mathematics and Statistics.
3. Software Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Software Engineering department.
two (2) other Science subjects.
4. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
5. Biochemistry
To study this course, candidates aspiring to gain admission into Biochemistry department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
6. Education and Chemistry
To study this course, the minimum requirement for applicants seeking admission to the Education and Chemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology and Agricultural Science.
7. Surveying and Geoinformatics
To study this course, candidates seeking admission into the Surveying and Geoinformatics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Nigerian Tertiary Institutions Offering Mechatronics and System Engineering Course