If you are planning to study Forestry and Wood Technology at Caleb University located in Lagos State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Caleb University was established in 2008 as a private university in Lagos State to provide quality higher education with emphasis on leadership, entrepreneurship, and innovation. This page explains everything you need to know to increase your chances of gaining admission into Caleb University.
Does Caleb University (CUI) offer Forestry and Wood Technology?
No, Caleb University does not offer Forestry and Wood Technology under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Caleb University (CUI) below to check if the Forestry and Wood Technology course under the Faculty of Agriculture has been updated.
Admission Requirements for Forestry and Wood Technology When Accredited in Caleb University (CUI)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Forestry and Wood Technology department under Faculty of Agriculture.
Biology / Agricultural Science,
at least ‘O’ Level pass in Physics.
JAMB Subject Combination
Mathematics / Physics and
Biology / Agricultural Science.
Caleb University Cut-Off Mark for Forestry and Wood Technology
The general UTME cut-off mark is 180, but due to the variation of Forestry and Wood Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Caleb University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Caleb University Science Courses with their Requirements
1. Computer Science (CS)
To study this course, the minimum requirement for applicants seeking admission to the Computer Science (CS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other Science subjects.
2. Physics
To study this course, candidates aspiring to gain admission into Physics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Chemistry, Mathematics and
any other Science subject from
Biology / Agricultural Science.
3. Zoology and Aquaculture
To study this course, the minimum requirement for applicants seeking admission to the Zoology and Aquaculture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
two (2) other Science subject.
4. Architecture
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
5. Plant Science and Biotechnology
To study this course, the minimum requirement for applicants seeking admission to the Plant Science and Biotechnology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
6. Building
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
7. Microbiology and Industrial Biotechnology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Microbiology and Industrial Biotechnology department.
Nigerian Tertiary Institutions Offering Forestry and Wood Technology Course