If you are planning to study Glass Technology at Caleb University located in Lagos State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Caleb University was established in 2008 as a private university in Lagos State to provide quality higher education with emphasis on leadership, entrepreneurship, and innovation. This page explains everything you need to know to increase your chances of gaining admission into Caleb University.
Does Caleb University (CUI) offer Glass Technology?
No, Caleb University does not offer Glass Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Caleb University (CUI) below to check if the Glass Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Glass Technology When Accredited in Caleb University (CUI)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Glass Technology department under Faculty of Engineering / Technology.
Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Ceramics, Graphic Design, Graphic Printing, Decorative Painting,
Spray Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Building / Engineering Drawing, General Wood Work.
Caleb University Cut-Off Mark for Glass Technology
The general UTME cut-off mark is 180, but due to the variation of Glass Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Caleb University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Caleb University Science Courses with their Requirements
1. Physics with Computational Modeling
To study this course, candidates seeking admission into the Physics with Computational Modeling department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Chemistry, Mathematics and
any other Science subject from:
Biology or Agricultural Science.
2. Architecture
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
3. Industrial Chemistry
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Industrial Chemistry department.
Biology / Agricultural Science.
4. Statistics
To study this course, candidates aspiring to gain admission into Statistics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other relevant subject.
5. Mathematics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mathematics department.
any two (2) other relevant subjects.
6. Zoology and Aquaculture
To study this course, the minimum requirement for applicants seeking admission to the Zoology and Aquaculture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
two (2) other Science subject.
7. Building
To study this course, the minimum requirement for applicants seeking admission to the Building department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Nigerian Tertiary Institutions Offering Glass Technology Course