If you are planning to study Livestock Production Technology at Caleb University located in Lagos State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Caleb University.
Does Caleb University (CUI) offer Livestock Production Technology?
No, Caleb University does not offer Livestock Production Technology under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Caleb University (CUI) below to check if the Livestock Production Technology course under the Faculty of Agriculture has been updated.
Admission Requirements for Livestock Production Technology When Accredited in Caleb University (CUI)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Livestock Production Technology department under Faculty of Agriculture, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science.
JAMB Subject Combination
Biology / Agricultural Science.
Caleb University Cut-Off Mark for Livestock Production Technology
The general UTME cut-off mark is 180, but due to the variation of Livestock Production Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Caleb University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Caleb University Science Courses with their Requirements
1. Environmental Management and Toxicology
To study this course, candidates seeking admission into the Environmental Management and Toxicology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
2. Microbiology and Industrial Biotechnology
To study this course, the minimum requirement for applicants seeking admission to the Microbiology and Industrial Biotechnology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
3. Quantity Surveying (QS)
To study this course, candidates aspiring to gain admission into Quantity Surveying (QS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
4. Architecture
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
5. Microbiology
To study this course, candidates seeking admission into the Microbiology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
6. Building
To study this course, candidates aspiring to gain admission into Building department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
7. Physics with Computational Modeling
To study this course, candidates seeking admission into the Physics with Computational Modeling department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Chemistry, Mathematics and
any other Science subject from:
Biology or Agricultural Science.
Nigerian Tertiary Institutions Offering Livestock Production Technology Course