If you are planning to study Mechatronics Engineering at Caleb University located in Lagos State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Caleb University.
Does Caleb University (CUI) offer Mechatronics Engineering?
No, Caleb University does not offer Mechatronics Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Caleb University (CUI) below to check if the Mechatronics Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechatronics Engineering When Accredited in Caleb University (CUI)
O’Level Requirements
To study this course, candidates seeking admission into the Mechatronics Engineering department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Caleb University Cut-Off Mark for Mechatronics Engineering
The general UTME cut-off mark is 180, but due to the variation of Mechatronics Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Caleb University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Caleb University Science Courses with their Requirements
1. Industrial Chemistry
To study this course, candidates aspiring to gain admission into Industrial Chemistry department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science.
2. Building
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
3. Chemistry
To study this course, the minimum requirement for applicants seeking admission to the Chemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
4. Environmental Management and Toxicology
To study this course, the minimum requirement for applicants seeking admission to the Environmental Management and Toxicology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
5. Quantity Surveying (QS)
To study this course, candidates aspiring to gain admission into Quantity Surveying (QS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
6. Architecture
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
7. Computer Science (CS)
To study this course, candidates aspiring to gain admission into Computer Science (CS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other Science subjects.
Nigerian Universities Offering Mechatronics Engineering Course