If you are planning to study Polymer and Textile Engineering at Caleb University located in Lagos State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Caleb University was established in 2008 as a private university in Lagos State to provide quality higher education with emphasis on leadership, entrepreneurship, and innovation. This page explains everything you need to know to increase your chances of gaining admission into Caleb University.
Does Caleb University (CUI) offer Polymer and Textile Engineering?
No, Caleb University does not offer Polymer and Textile Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Caleb University (CUI) below to check if the Polymer and Textile Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Polymer and Textile Engineering When Accredited in Caleb University (CUI)
O’Level Requirements
To study this course, candidates seeking admission into the Polymer and Textile Engineering department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Caleb University Cut-Off Mark for Polymer and Textile Engineering
The general UTME cut-off mark is 180, but due to the variation of Polymer and Textile Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Caleb University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Caleb University Science Courses with their Requirements
1. Architecture
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
2. Building
To study this course, candidates seeking admission into the Building department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
3. Zoology and Aquaculture
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Zoology and Aquaculture department.
two (2) other Science subject.
4. Cyber Security
To study this course, candidates seeking admission into the Cyber Security department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects.
5. Physics with Computational Modeling
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Physics with Computational Modeling department.
Chemistry, Mathematics and
any other Science subject from:
Biology or Agricultural Science.
6. Industrial Chemistry
To study this course, the minimum requirement for applicants seeking admission to the Industrial Chemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science.
7. Microbiology
To study this course, the minimum requirement for applicants seeking admission to the Microbiology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Nigerian Tertiary Institutions Offering Polymer and Textile Engineering Course