If you are planning to study Prosthesis and Orthopaedic Technology at Caleb University located in Lagos State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Caleb University was established in 2008 as a private university in Lagos State to provide quality higher education with emphasis on leadership, entrepreneurship, and innovation. This page explains everything you need to know to increase your chances of gaining admission into Caleb University.
Does Caleb University (CUI) offer Prosthesis and Orthopaedic Technology?
No, Caleb University does not offer Prosthesis and Orthopaedic Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Caleb University (CUI) below to check if the Prosthesis and Orthopaedic Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Prosthesis and Orthopaedic Technology When Accredited in Caleb University (CUI)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Prosthesis and Orthopaedic Technology department under Faculty of Engineering / Technology.
Caleb University Cut-Off Mark for Prosthesis and Orthopaedic Technology
The general UTME cut-off mark is 180, but due to the variation of Prosthesis and Orthopaedic Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Caleb University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Caleb University Science Courses with their Requirements
1. Microbiology and Industrial Biotechnology
To study this course, candidates aspiring to gain admission into Microbiology and Industrial Biotechnology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
2. Zoology and Aquaculture
To study this course, candidates seeking admission into the Zoology and Aquaculture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subject.
3. Quantity Surveying (QS)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Quantity Surveying (QS) department.
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
4. Microbiology
To study this course, candidates aspiring to gain admission into Microbiology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
5. Architecture
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
6. Cyber Security
To study this course, candidates seeking admission into the Cyber Security department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects.
7. Environmental Management and Toxicology
To study this course, candidates seeking admission into the Environmental Management and Toxicology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Nigerian Tertiary Institutions Offering Prosthesis and Orthopaedic Technology Course