If you are planning to study Textile Science and Technology at Caleb University located in Lagos State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Caleb University was established in 2008 as a private university in Lagos State to provide quality higher education with emphasis on leadership, entrepreneurship, and innovation. This page explains everything you need to know to increase your chances of gaining admission into Caleb University.
Does Caleb University (CUI) offer Textile Science and Technology?
No, Caleb University does not offer Textile Science and Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Caleb University (CUI) below to check if the Textile Science and Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Textile Science and Technology When Accredited in Caleb University (CUI)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Textile Science and Technology department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Caleb University Cut-Off Mark for Textile Science and Technology
The general UTME cut-off mark is 180, but due to the variation of Textile Science and Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Caleb University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Caleb University Science Courses with their Requirements
1. Zoology and Aquaculture
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Zoology and Aquaculture department.
two (2) other Science subject.
2. Quantity Surveying (QS)
To study this course, the minimum requirement for applicants seeking admission to the Quantity Surveying (QS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
3. Building
To study this course, candidates seeking admission into the Building department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
4. Cyber Security
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Cyber Security department.
two (2) other Science subjects.
5. Microbiology and Industrial Biotechnology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Microbiology and Industrial Biotechnology department.
6. Biochemistry
To study this course, candidates seeking admission into the Biochemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
7. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Nigerian Tertiary Institutions Offering Textile Science and Technology Course