If you are planning to study Crop, Soil and Pest Management at Covenant University, Ota located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Covenant University.
Does Covenant University, Ota (CU) offer Crop, Soil and Pest Management?
No, Covenant University, Ota does not offer Crop, Soil and Pest Management under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Covenant University, Ota (CU) below to check if the Crop, Soil and Pest Management course under the Faculty of Agriculture has been updated.
Admission Requirements for Crop, Soil and Pest Management When Accredited in Covenant University, Ota (CU)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Crop, Soil and Pest Management department under Faculty of Agriculture.
Biology / Agricultural Science,
one Science/Social Science subject and
at least ‘O’ Level pass in Physics.
JAMB Subject Combination
Biology / Agriculture and
Covenant University Cut-Off Mark for Crop, Soil and Pest Management
The general UTME cut-off mark is 180, but due to the variation of Crop, Soil and Pest Management cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Covenant University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Covenant University Science Courses with their Requirements
1. Electrical / Electronics Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Electrical / Electronics Engineering department.
any other Science subject.
2. Industrial Physics With Electronics and IT Application
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Industrial Physics With Electronics and IT Application department.
Mathematics and one (1) other Science.
3. Biology
To study this course, the minimum requirement for applicants seeking admission to the Biology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Mathematics / Physics and
any one other relevant subject.
4. Petroleum Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Petroleum Engineering department.
5. Architecture
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
6. Civil Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Civil Engineering department.
7. Building Technology (BT)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Nigerian Tertiary Institutions Offering Crop, Soil and Pest Management Course