If you are planning to study Electrical and Electronics Engineering (EEE) at Covenant University, Ota located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Covenant University was established in 2002 by the Living Faith Church Worldwide as a private Christian university dedicated to raising a new generation of leaders through quality education, research, and innovation. It has since become one of Nigeria’s leading private universities. This page explains everything you need to know to increase your chances of gaining admission into Covenant University.
Does Covenant University, Ota (CU) offer Electrical and Electronics Engineering?
No, Covenant University, Ota does not offer Electrical and Electronics Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Covenant University, Ota (CU) below to check if the Electrical and Electronics Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Electrical and Electronics Engineering (EEE) When Accredited in Covenant University, Ota (CU)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Electrical and Electronics Engineering (EEE) department under Faculty of Engineering / Technology.
any other Science subject.
Covenant University Cut-Off Mark for Electrical and Electronics Engineering (EEE)
The general UTME cut-off mark is 180, but due to the variation of Electrical and Electronics Engineering (EEE) cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Covenant University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Covenant University Science Courses with their Requirements
1. Biochemistry
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Biochemistry department.
2. Building Technology (BT)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
3. Industrial Physics With Renewable Energy
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Industrial Physics With Renewable Energy department.
4. Mechanical Engineering
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant Science subjects.
5. Industrial Physics With Electronics and IT Application
To study this course, candidates aspiring to gain admission into Industrial Physics With Electronics and IT Application department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Mathematics and one (1) other Science.
6. Architecture
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
7. Civil Engineering
To study this course, candidates aspiring to gain admission into Civil Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Nigerian Universities Offering Electrical and Electronics Engineering Course