If you are planning to study Glass Technology at Covenant University, Ota located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Covenant University.
Does Covenant University, Ota (CU) offer Glass Technology?
No, Covenant University, Ota does not offer Glass Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Covenant University, Ota (CU) below to check if the Glass Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Glass Technology When Accredited in Covenant University, Ota (CU)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Glass Technology department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Ceramics, Graphic Design, Graphic Printing, Decorative Painting,
Spray Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Building / Engineering Drawing, General Wood Work.
Covenant University Cut-Off Mark for Glass Technology
The general UTME cut-off mark is 180, but due to the variation of Glass Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Covenant University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Covenant University Science Courses with their Requirements
Computer Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Computer Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Civil Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Civil Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Architecture
SSCE Requirements
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Industrial Chemistry
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Industrial Chemistry department.
Biology / Agricultural Science.
Mechanical Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Mechanical Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant Science subjects.
Electrical / Electronics Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronics Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
Nigerian Tertiary Institutions Offering Glass Technology Course