If you are planning to study Metallurgical Engineering at Covenant University, Ota located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Covenant University was established in 2002 by the Living Faith Church Worldwide as a private Christian university dedicated to raising a new generation of leaders through quality education, research, and innovation. It has since become one of Nigeria’s leading private universities. This page explains everything you need to know to increase your chances of gaining admission into Covenant University.
Does Covenant University, Ota (CU) offer Metallurgical Engineering?
No, Covenant University, Ota does not offer Metallurgical Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Covenant University, Ota (CU) below to check if the Metallurgical Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Metallurgical Engineering When Accredited in Covenant University, Ota (CU)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Metallurgical Engineering department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
one other Science subject.
Covenant University Cut-Off Mark for Metallurgical Engineering
The general UTME cut-off mark is 180, but due to the variation of Metallurgical Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Covenant University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Covenant University Science Courses with their Requirements
1. Computer Science (CS)
To study this course, candidates seeking admission into the Computer Science (CS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other Science subjects.
2. Industrial Physics With Electronics and IT Application
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Industrial Physics With Electronics and IT Application department.
Mathematics and one (1) other Science.
3. Building Technology (BT)
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
4. Industrial Physics With Applied Geophysics
To study this course, candidates aspiring to gain admission into Industrial Physics With Applied Geophysics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
5. Architecture
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
6. Industrial Mathematics
To study this course, candidates seeking admission into the Industrial Mathematics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects.
7. Biology
To study this course, candidates seeking admission into the Biology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Mathematics / Physics and
any one other relevant subject.
Nigerian Tertiary Institutions Offering Metallurgical Engineering Course