If you are planning to study Software Engineering and Digital Entrepreneurship at Covenant University, Ota located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Covenant University was established in 2002 by the Living Faith Church Worldwide as a private Christian university dedicated to raising a new generation of leaders through quality education, research, and innovation. It has since become one of Nigeria’s leading private universities. This page explains everything you need to know to increase your chances of gaining admission into Covenant University.
Does Covenant University, Ota (CU) offer Software Engineering and Digital Entrepreneurship?
No, Covenant University, Ota does not offer Software Engineering and Digital Entrepreneurship under its Faculty of Data and Decision Sciences. However, since our course list is updated regularly, you can visit the courses available at Covenant University, Ota (CU) below to check if the Software Engineering and Digital Entrepreneurship course under the Faculty of Data and Decision Sciences has been updated.
Admission Requirements for Software Engineering and Digital Entrepreneurship When Accredited in Covenant University, Ota (CU)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Software Engineering and Digital Entrepreneurship department under Faculty of Data and Decision Sciences.
three (3) other relevant subjects.
JAMB Subject Combination
two (2) other relevant subjects.
Covenant University Cut-Off Mark for Software Engineering and Digital Entrepreneurship
The general UTME cut-off mark is 180, but due to the variation of Software Engineering and Digital Entrepreneurship cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Covenant University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Covenant University Science Courses with their Requirements
1. Civil Engineering
To study this course, the minimum requirement for applicants seeking admission to the Civil Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
2. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
3. Electrical / Electronics Engineering
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronics Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
4. Industrial Physics With Renewable Energy
To study this course, candidates seeking admission into the Industrial Physics With Renewable Energy department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
5. Building Technology (BT)
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
6. Mechanical Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Engineering department.
any two (2) other relevant Science subjects.
7. Chemical Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Chemical Engineering department.
any other Science subject.
Nigerian Tertiary Institutions Offering Software Engineering and Digital Entrepreneurship Course