If you are planning to study Mechanical Metalwork Technology Education at Crescent University located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Crescent University was established in 2005 by the Islamic Mission for Africa as a private university in Abeokuta, Ogun State. It was created to combine sound academic training with moral and ethical values inspired by Islamic principles. This page explains everything you need to know to increase your chances of gaining admission into Crescent University.
Does Crescent University (CU) offer Mechanical Metalwork Technology Education?
No, Crescent University does not offer Mechanical Metalwork Technology Education under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Crescent University (CU) below to check if the Mechanical Metalwork Technology Education course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechanical Metalwork Technology Education When Accredited in Crescent University (CU)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Metalwork Technology Education department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
one (1) of Biology /Agricultural Science; Physics, or Chemistry and
two (2) from General Science/IntegratedScience, Technical Drawing/Fine Art, Health Science Food and Nutrition,
Geography, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
JAMB Subject Combination
any other relevant subject.
Crescent University Cut-Off Mark for Mechanical Metalwork Technology Education
The general UTME cut-off mark is 180, but due to the variation of Mechanical Metalwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Crescent University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Crescent University Science Courses with their Requirements
1. Mathematics
To study this course, the minimum requirement for applicants seeking admission to the Mathematics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subjects.
2. Chemistry
To study this course, candidates aspiring to gain admission into Chemistry department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
3. Environmental Management
To study this course, candidates aspiring to gain admission into Environmental Management department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other four (4) relevant subjects plus a pass in English Language.
4. Urban and Regional Planning (URP)
To study this course, candidates aspiring to gain admission into Urban and Regional Planning (URP) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
5. Computer Science (CS)
To study this course, the minimum requirement for applicants seeking admission to the Computer Science (CS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other Science subjects.
6. Architecture
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
7. Microbiology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Microbiology department.
Nigerian Tertiary Institutions Offering Mechanical Metalwork Technology Education Course