If you are planning to study Applied Microbiology and Brewing at Delta State University of Science and Technology located in Delta State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. DSUST was established in 2021 by the Delta State Government to advance science, technology, engineering, and innovation-driven education. The university was created to support technological development and economic transformation. This page explains everything you need to know to increase your chances of gaining admission into DSUST.
Does Delta State University of Science and Technology (DSUST) offer Applied Microbiology and Brewing?
No, Delta State University of Science and Technology does not offer Applied Microbiology and Brewing under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Delta State University of Science and Technology (DSUST) below to check if the Applied Microbiology and Brewing course under the Faculty of Science has been updated.
Admission Requirements for Applied Microbiology and Brewing When Accredited in Delta State University of Science and Technology (DSUST)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Applied Microbiology and Brewing department under Faculty of Science, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology or Health Science.
DSUST Cut-Off Mark for Applied Microbiology and Brewing
The general UTME cut-off mark is 180, but due to the variation of Applied Microbiology and Brewing cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from DSUST Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other DSUST Science Courses with their Requirements
1. Quantity Surveying (QS)
To study this course, candidates aspiring to gain admission into Quantity Surveying (QS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
2. Soil Science
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Soil Science department.
Biology / Agricultural Science and
any other Science subject.
3. Computer Engineering
To study this course, candidates seeking admission into the Computer Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
4. Mathematics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mathematics department.
any two (2) other relevant subjects.
5. Environmental Management and Toxicology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Environmental Management and Toxicology department.
6. Surveying and Geoinformatics
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
7. Mechanical Engineering
To study this course, candidates aspiring to gain admission into Mechanical Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant Science subjects.
Nigerian Tertiary Institutions Offering Applied Microbiology and Brewing Course