If you are planning to study Crop Production Technology at Delta State University of Science and Technology located in Delta State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. DSUST was established in 2021 by the Delta State Government to advance science, technology, engineering, and innovation-driven education. The university was created to support technological development and economic transformation. This page explains everything you need to know to increase your chances of gaining admission into DSUST.
Does Delta State University of Science and Technology (DSUST) offer Crop Production Technology?
No, Delta State University of Science and Technology does not offer Crop Production Technology under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Delta State University of Science and Technology (DSUST) below to check if the Crop Production Technology course under the Faculty of Agriculture has been updated.
Admission Requirements for Crop Production Technology When Accredited in Delta State University of Science and Technology (DSUST)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Crop Production Technology department under Faculty of Agriculture, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science,
one Science/Social Science subject and
at least a pass in Physics.
DSUST Cut-Off Mark for Crop Production Technology
The general UTME cut-off mark is 180, but due to the variation of Crop Production Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from DSUST Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other DSUST Science Courses with their Requirements
1. Environmental Management
To study this course, candidates seeking admission into the Environmental Management department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other four (4) relevant subjects plus a pass in English Language.
2. Mathematics
To study this course, candidates aspiring to gain admission into Mathematics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subjects.
3. Surveying and Geoinformatics
To study this course, candidates seeking admission into the Surveying and Geoinformatics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
4. Chemistry
To study this course, candidates seeking admission into the Chemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
5. Electrical Engineering
To study this course, the minimum requirement for applicants seeking admission to the Electrical Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
6. Chemical Engineering
To study this course, the minimum requirement for applicants seeking admission to the Chemical Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
7. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Nigerian Tertiary Institutions Offering Crop Production Technology Course