If you are planning to study Geology and Geophysics at Delta State University of Science and Technology located in Delta State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into DSUST.
Does Delta State University of Science and Technology (DSUST) offer Geology and Geophysics?
No, Delta State University of Science and Technology does not offer Geology and Geophysics under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Delta State University of Science and Technology (DSUST) below to check if the Geology and Geophysics course under the Faculty of Science has been updated.
Admission Requirements for Geology and Geophysics When Accredited in Delta State University of Science and Technology (DSUST)
O’Level Requirements
To study this course, candidates seeking admission into the Geology and Geophysics department under Faculty of Science, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
JAMB Subject Combination
Mathematics, Biology and Geography.
DSUST Cut-Off Mark for Geology and Geophysics
The general UTME cut-off mark is 180, but due to the variation of Geology and Geophysics cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from DSUST Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other DSUST Science Courses with their Requirements
Petroleum Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Petroleum Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Mathematics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mathematics department.
any two (2) other relevant subjects.
Environmental Management
SSCE Requirements
To study this course, candidates aspiring to gain admission into Environmental Management department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other four (4) relevant subjects plus a pass in English Language.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates seeking admission into the Urban and Regional Planning (URP) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Architecture
SSCE Requirements
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Mechanical Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Engineering department.
any two (2) other relevant Science subjects.
Nigerian Tertiary Institutions Offering Geology and Geophysics Course