If you are planning to study Mechanical Metalwork Technology Education at Delta State University of Science and Technology located in Delta State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. DSUST was established in 2021 by the Delta State Government to advance science, technology, engineering, and innovation-driven education. The university was created to support technological development and economic transformation. This page explains everything you need to know to increase your chances of gaining admission into DSUST.
Does Delta State University of Science and Technology (DSUST) offer Mechanical Metalwork Technology Education?
No, Delta State University of Science and Technology does not offer Mechanical Metalwork Technology Education under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Delta State University of Science and Technology (DSUST) below to check if the Mechanical Metalwork Technology Education course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechanical Metalwork Technology Education When Accredited in Delta State University of Science and Technology (DSUST)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Metalwork Technology Education department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
one (1) of Biology /Agricultural Science; Physics, or Chemistry and
two (2) from General Science/IntegratedScience, Technical Drawing/Fine Art, Health Science Food and Nutrition,
Geography, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
JAMB Subject Combination
any other relevant subject.
DSUST Cut-Off Mark for Mechanical Metalwork Technology Education
The general UTME cut-off mark is 180, but due to the variation of Mechanical Metalwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from DSUST Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other DSUST Science Courses with their Requirements
1. Statistics
To study this course, candidates seeking admission into the Statistics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other relevant subject.
2. Petroleum Engineering
To study this course, candidates seeking admission into the Petroleum Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
3. Computer Engineering
To study this course, candidates aspiring to gain admission into Computer Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
4. Urban and Regional Planning (URP)
To study this course, the minimum requirement for applicants seeking admission to the Urban and Regional Planning (URP) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
5. Agricultural Engineering (AE)
To study this course, candidates aspiring to gain admission into Agricultural Engineering (AE) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any one other subject from:
Introduction to Agricultural Science,
Materials and Workshop Process and Machining,
Tractor Layout Power Unit Under Carriage and Auto Electricity;
Transmission System;
Implement and Machine;
Principles of Crop Husbandry and Land Use,
Materials and Workshop Processes;
Construction and Maintenance of Agricultural Machines;
General Metal Work;
General Wood Work and Building / Engineering Drawing.
6. Software Engineering
To study this course, the minimum requirement for applicants seeking admission to the Software Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
two (2) other Science subjects.
7. Building Technology (BT)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Nigerian Tertiary Institutions Offering Mechanical Metalwork Technology Education Course