If you are planning to study Metalwork Technology Education at Delta State University of Science and Technology located in Delta State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. DSUST was established in 2021 by the Delta State Government to advance science, technology, engineering, and innovation-driven education. The university was created to support technological development and economic transformation. This page explains everything you need to know to increase your chances of gaining admission into DSUST.
Does Delta State University of Science and Technology (DSUST) offer Metalwork Technology Education?
No, Delta State University of Science and Technology does not offer Metalwork Technology Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Delta State University of Science and Technology (DSUST) below to check if the Metalwork Technology Education course under the Faculty of Education has been updated.
Admission Requirements for Metalwork Technology Education When Accredited in Delta State University of Science and Technology (DSUST)
O’Level Requirements
To study this course, candidates seeking admission into the Metalwork Technology Education department under Faculty of Education, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science, Physics, or Chemistry
and two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
DSUST Cut-Off Mark for Metalwork Technology Education
The general UTME cut-off mark is 180, but due to the variation of Metalwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from DSUST Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other DSUST Science Courses with their Requirements
1. Environmental Management and Toxicology
To study this course, the minimum requirement for applicants seeking admission to the Environmental Management and Toxicology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
2. Quantity Surveying (QS)
To study this course, the minimum requirement for applicants seeking admission to the Quantity Surveying (QS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
3. Physics
To study this course, candidates aspiring to gain admission into Physics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Chemistry, Mathematics and
any other Science subject from
Biology / Agricultural Science.
4. Chemical Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Chemical Engineering department.
any other Science subject.
5. Urban and Regional Planning (URP)
To study this course, candidates aspiring to gain admission into Urban and Regional Planning (URP) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
6. Building Technology (BT)
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
7. Petroleum Chemistry
To study this course, candidates seeking admission into the Petroleum Chemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Nigerian Tertiary Institutions Offering Metalwork Technology Education Course