If you are planning to study Physical Education at Delta State University of Science and Technology located in Delta State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. DSUST was established in 2021 by the Delta State Government to advance science, technology, engineering, and innovation-driven education. The university was created to support technological development and economic transformation. This page explains everything you need to know to increase your chances of gaining admission into DSUST.
Does Delta State University of Science and Technology (DSUST) offer Physical Education?
No, Delta State University of Science and Technology does not offer Physical Education under its Faculty of Health and Medical Sciences. However, since our course list is updated regularly, you can visit the courses available at Delta State University of Science and Technology (DSUST) below to check if the Physical Education course under the Faculty of Health and Medical Sciences has been updated.
Admission Requirements for Physical Education When Accredited in Delta State University of Science and Technology (DSUST)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Physical Education department under Faculty of Health and Medical Sciences, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology or its Equivalent,
any two (2) relevant subjects.
JAMB Subject Combination
any two (2) relevant subjects.
DSUST Cut-Off Mark for Physical Education
The general UTME cut-off mark is 180, but due to the variation of Physical Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from DSUST Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other DSUST Science Courses with their Requirements
1. Marine Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Marine Engineering department.
2. Computer Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Engineering department.
3. Physics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Physics department.
Chemistry, Mathematics and
any other Science subject from
Biology / Agricultural Science.
4. Crop Science
To study this course, the minimum requirement for applicants seeking admission to the Crop Science department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science,
one Science/Social Science subject and
at least a pass in Physics is required.
5. Petroleum Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Petroleum Engineering department.
6. Architecture
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
7. Agricultural Engineering (AE)
To study this course, the minimum requirement for applicants seeking admission to the Agricultural Engineering (AE) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Any one other subject from:
Introduction to Agricultural Science,
Materials and Workshop Process and Machining,
Tractor Layout Power Unit Under Carriage and Auto Electricity;
Transmission System;
Implement and Machine;
Principles of Crop Husbandry and Land Use,
Materials and Workshop Processes;
Construction and Maintenance of Agricultural Machines;
General Metal Work;
General Wood Work and Building / Engineering Drawing.
Nigerian Universities Offering Physical Education Course