If you are planning to study Prosthesis and Orthopaedic Technology at Delta State University of Science and Technology located in Delta State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into DSUST.
Does Delta State University of Science and Technology (DSUST) offer Prosthesis and Orthopaedic Technology?
No, Delta State University of Science and Technology does not offer Prosthesis and Orthopaedic Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Delta State University of Science and Technology (DSUST) below to check if the Prosthesis and Orthopaedic Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Prosthesis and Orthopaedic Technology When Accredited in Delta State University of Science and Technology (DSUST)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Prosthesis and Orthopaedic Technology department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
DSUST Cut-Off Mark for Prosthesis and Orthopaedic Technology
The general UTME cut-off mark is 180, but due to the variation of Prosthesis and Orthopaedic Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from DSUST Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other DSUST Science Courses with their Requirements
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Environmental Management and Toxicology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Environmental Management and Toxicology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Architecture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Biology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Biology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Mathematics / Physics and
any one other relevant subject.
Petroleum Chemistry
SSCE Requirements
To study this course, candidates seeking admission into the Petroleum Chemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Environmental Management
SSCE Requirements
To study this course, candidates aspiring to gain admission into Environmental Management department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other four (4) relevant subjects plus a pass in English Language.
Mechanical Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant Science subjects.
Nigerian Tertiary Institutions Offering Prosthesis and Orthopaedic Technology Course