If you are planning to study Technical Education at Delta State University of Science and Technology located in Delta State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. DSUST was established in 2021 by the Delta State Government to advance science, technology, engineering, and innovation-driven education. The university was created to support technological development and economic transformation. This page explains everything you need to know to increase your chances of gaining admission into DSUST.
Does Delta State University of Science and Technology (DSUST) offer Technical Education?
No, Delta State University of Science and Technology does not offer Technical Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Delta State University of Science and Technology (DSUST) below to check if the Technical Education course under the Faculty of Education has been updated.
Admission Requirements for Technical Education When Accredited in Delta State University of Science and Technology (DSUST)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Technical Education department under Faculty of Education, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any three (3) relevant subjects.
DSUST Cut-Off Mark for Technical Education
The general UTME cut-off mark is 180, but due to the variation of Technical Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from DSUST Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other DSUST Science Courses with their Requirements
1. Environmental Management and Toxicology
To study this course, the minimum requirement for applicants seeking admission to the Environmental Management and Toxicology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
2. Urban and Regional Planning (URP)
To study this course, the minimum requirement for applicants seeking admission to the Urban and Regional Planning (URP) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
3. Marine Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Marine Engineering department.
4. Cyber Security
To study this course, candidates aspiring to gain admission into Cyber Security department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
two (2) other Science subjects.
5. Building Technology (BT)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
6. Environmental Management
To study this course, candidates seeking admission into the Environmental Management department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other four (4) relevant subjects plus a pass in English Language.
7. Quantity Surveying (QS)
To study this course, candidates seeking admission into the Quantity Surveying (QS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
Nigerian Universities Offering Technical Education Course