If you are planning to study Crop Production Technology at Enugu State University of Science & Technology located in Enugu State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ESUT.
Does Enugu State University of Science & Technology (ESUT) offer Crop Production Technology?
No, Enugu State University of Science & Technology does not offer Crop Production Technology under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Enugu State University of Science & Technology (ESUT) below to check if the Crop Production Technology course under the Faculty of Agriculture has been updated.
Admission Requirements for Crop Production Technology When Accredited in Enugu State University of Science & Technology (ESUT)
O’Level Requirements
To study this course, candidates seeking admission into the Crop Production Technology department under Faculty of Agriculture, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science,
one Science/Social Science subject and
at least a pass in Physics.
ESUT Cut-Off Mark for Crop Production Technology
The general UTME cut-off mark is 180, but due to the variation of Crop Production Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ESUT Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ESUT Science Courses with their Requirements
1. Industrial Physics
To study this course, candidates seeking admission into the Industrial Physics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject from Further Mathematics and Biology or Agricultural Science.
2. Quantity Surveying (QS)
To study this course, candidates seeking admission into the Quantity Surveying (QS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
3. Medicine and Surgery
To study this course, candidates aspiring to gain admission into Medicine and Surgery department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
4. Medical Laboratory Science
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Medical Laboratory Science department.
5. Surveying and Geoinformatics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
6. Building
To study this course, the minimum requirement for applicants seeking admission to the Building department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
7. Mechanical / Production Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical / Production Engineering department.
any other Science subject.
Nigerian Tertiary Institutions Offering Crop Production Technology Course