If you are planning to study Environmental Management and Pollution Control at Enugu State University of Science & Technology located in Enugu State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ESUT.
Does Enugu State University of Science & Technology (ESUT) offer Environmental Management and Pollution Control?
No, Enugu State University of Science & Technology does not offer Environmental Management and Pollution Control under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Enugu State University of Science & Technology (ESUT) below to check if the Environmental Management and Pollution Control course under the Faculty of Science has been updated.
Admission Requirements for Environmental Management and Pollution Control When Accredited in Enugu State University of Science & Technology (ESUT)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Environmental Management and Pollution Control department under Faculty of Science.
ESUT Cut-Off Mark for Environmental Management and Pollution Control
The general UTME cut-off mark is 180, but due to the variation of Environmental Management and Pollution Control cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ESUT Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ESUT Science Courses with their Requirements
Education and Biology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Education and Biology department.
Food Science and Technology (FT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Food Science and Technology (FT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Agriculture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Agriculture department.
Biology / Agricultural Science,
Mathematics / Physics, and
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Geography and Meteorology
SSCE Requirements
To study this course, candidates seeking admission into the Geography and Meteorology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Arts or Social Science subjects with at least a pass in Mathematics.
Building and Woodwork Technology Education
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building and Woodwork Technology Education department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
Architecture
SSCE Requirements
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Nigerian Tertiary Institutions Offering Environmental Management and Pollution Control Course