If you are planning to study Metallurgical Engineering at Enugu State University of Science & Technology located in Enugu State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. ESUT was established in 1980 as Anambra State University of Technology before becoming Enugu State University of Science and Technology in 1991 following the creation of Enugu State. It is recognized as one of Nigeria’s pioneering universities of technology. This page explains everything you need to know to increase your chances of gaining admission into ESUT.
Does Enugu State University of Science & Technology (ESUT) offer Metallurgical Engineering?
No, Enugu State University of Science & Technology does not offer Metallurgical Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Enugu State University of Science & Technology (ESUT) below to check if the Metallurgical Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Metallurgical Engineering When Accredited in Enugu State University of Science & Technology (ESUT)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Metallurgical Engineering department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
one other Science subject.
ESUT Cut-Off Mark for Metallurgical Engineering
The general UTME cut-off mark is 180, but due to the variation of Metallurgical Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ESUT Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ESUT Science Courses with their Requirements
1. Biology
To study this course, the minimum requirement for applicants seeking admission to the Biology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Mathematics / Physics and
any one other relevant subject.
2. Applied Microbiology
To study this course, candidates aspiring to gain admission into Applied Microbiology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology or Health Science.
3. Land Surveying
To study this course, candidates seeking admission into the Land Surveying department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing.
4. Mechanical / Production Engineering
To study this course, candidates seeking admission into the Mechanical / Production Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
5. Quantity Surveying (QS)
To study this course, candidates aspiring to gain admission into Quantity Surveying (QS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
6. Industrial Chemistry
To study this course, candidates seeking admission into the Industrial Chemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science.
7. Geography and Meteorology
To study this course, candidates aspiring to gain admission into Geography and Meteorology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Arts or Social Science subjects with at least a pass in Mathematics.
Nigerian Tertiary Institutions Offering Metallurgical Engineering Course