If you are planning to study Prosthesis and Orthopaedic Technology at Enugu State University of Science & Technology located in Enugu State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. ESUT was established in 1980 as Anambra State University of Technology before becoming Enugu State University of Science and Technology in 1991 following the creation of Enugu State. It is recognized as one of Nigeria’s pioneering universities of technology. This page explains everything you need to know to increase your chances of gaining admission into ESUT.
Does Enugu State University of Science & Technology (ESUT) offer Prosthesis and Orthopaedic Technology?
No, Enugu State University of Science & Technology does not offer Prosthesis and Orthopaedic Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Enugu State University of Science & Technology (ESUT) below to check if the Prosthesis and Orthopaedic Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Prosthesis and Orthopaedic Technology When Accredited in Enugu State University of Science & Technology (ESUT)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Prosthesis and Orthopaedic Technology department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
ESUT Cut-Off Mark for Prosthesis and Orthopaedic Technology
The general UTME cut-off mark is 180, but due to the variation of Prosthesis and Orthopaedic Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ESUT Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ESUT Science Courses with their Requirements
1. Quantity Surveying (QS)
To study this course, the minimum requirement for applicants seeking admission to the Quantity Surveying (QS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
2. Biology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Biology department.
Mathematics / Physics and
any one other relevant subject.
3. Education and Integrated Science
To study this course, candidates aspiring to gain admission into Education and Integrated Science department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any other four (4) relevant subjects
4. Food Science and Technology (FT)
To study this course, the minimum requirement for applicants seeking admission to the Food Science and Technology (FT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
5. Computer Science (CS)
To study this course, candidates aspiring to gain admission into Computer Science (CS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other Science subjects.
6. Education and Physics
To study this course, candidates seeking admission into the Education and Physics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects or NTC / NBC.
7. Surveying and Geoinformatics
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Nigerian Tertiary Institutions Offering Prosthesis and Orthopaedic Technology Course