If you are planning to study Water Resources Engineering Technology at Enugu State University of Science & Technology located in Enugu State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. ESUT was established in 1980 as Anambra State University of Technology before becoming Enugu State University of Science and Technology in 1991 following the creation of Enugu State. It is recognized as one of Nigeria’s pioneering universities of technology. This page explains everything you need to know to increase your chances of gaining admission into ESUT.
Does Enugu State University of Science & Technology (ESUT) offer Water Resources Engineering Technology?
No, Enugu State University of Science & Technology does not offer Water Resources Engineering Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Enugu State University of Science & Technology (ESUT) below to check if the Water Resources Engineering Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Water Resources Engineering Technology When Accredited in Enugu State University of Science & Technology (ESUT)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Water Resources Engineering Technology department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
ESUT Cut-Off Mark for Water Resources Engineering Technology
The general UTME cut-off mark is 180, but due to the variation of Water Resources Engineering Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ESUT Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ESUT Science Courses with their Requirements
1. Applied Microbiology
To study this course, candidates aspiring to gain admission into Applied Microbiology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology or Health Science.
2. Building and Woodwork Technology Education
To study this course, the minimum requirement for applicants seeking admission to the Building and Woodwork Technology Education department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
3. Electrical / Electronics Technology Education
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Electrical / Electronics Technology Education department.
any other Science subject.
4. Food Science and Technology (FT)
To study this course, candidates aspiring to gain admission into Food Science and Technology (FT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
5. Architecture
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
6. Surveying and Geoinformatics
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
7. Mathematics and Statistics
To study this course, the minimum requirement for applicants seeking admission to the Mathematics and Statistics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology and Additional / Further Mathematics.
Nigerian Tertiary Institutions Offering Water Resources Engineering Technology Course