If you are planning to study Printing Technology at Federal Polytechnic, Mubi located in Adamawa State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into MUBIPOLY.
Does Federal Polytechnic, Mubi (MUBIPOLY) offer Printing Technology?
No, Federal Polytechnic, Mubi does not offer Printing Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Federal Polytechnic, Mubi (MUBIPOLY) below to check if the Printing Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Printing Technology When Accredited in Federal Polytechnic, Mubi (MUBIPOLY)
O’Level Requirements
To study this course, candidates seeking admission into the Printing Technology department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other subjects from:
Metal Work, Basic Electricity, Technical Drawing/Fine Art,
Book Keeping and Principles of Accounting, Economics/Commerce,
JAMB Subject Combination
Chemistry or Technical Drawing / Art.
MUBIPOLY Cut-Off Mark for Printing Technology
The general UTME cut-off mark is 180, but due to the variation of Printing Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from MUBIPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other MUBIPOLY Science Courses with their Requirements
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Animal Health and Production Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Animal Health and Production Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any three (3) of the following:
Geography, Food and Nutrition, Economics, Technical Drawing,
English Language, Physics, Chemistry, Nigerian Language, and Home Economics.
Food Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Food Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science,
any two of the following:
Geography, Food and Nutrition, Economics, Technical Drawing, Physics, Chemistry, Nigerian Language and Home Economics.
At least a pass in Chemistry is required.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Science Laboratory Technology (SLT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates seeking admission into the Urban and Regional Planning (URP) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Mechanical Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mechanical Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Production Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Production Technology department.
Biology/Agricultural Science,
any other relevant subject from the following:
Technical Drawing, Physics,
Nigerian Language, Home Economics.
Nigerian Polytechnics Offering Printing Technology Course