If you are planning to study Metallurgical and Material Engineering at Federal Polytechnic Nekede, Owerri located in Imo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FPNO.
Does Federal Polytechnic Nekede, Owerri (FPNO) offer Metallurgical and Material Engineering?
No, Federal Polytechnic Nekede, Owerri does not offer Metallurgical and Material Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Federal Polytechnic Nekede, Owerri (FPNO) below to check if the Metallurgical and Material Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Metallurgical and Material Engineering When Accredited in Federal Polytechnic Nekede, Owerri (FPNO)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Metallurgical and Material Engineering department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
one other Science subject.
FPNO Cut-Off Mark for Metallurgical and Material Engineering
The general UTME cut-off mark is 180, but due to the variation of Metallurgical and Material Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FPNO Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FPNO Science Courses with their Requirements
Optometry
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Optometry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Physics, Chemistry, Biology and
Additional / Further Mathematics.
Pharmaceutical Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Pharmaceutical Technology department.
any other one (1) relevant subject.
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Civil Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Civil Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any one other subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Agricultural Technology
SSCE Requirements
To study this course, candidates seeking admission into the Agricultural Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science,
Mathematics, Chemistry and
Geography, Food and Nutrition, Economics,
Technical Drawing, Physics, Nigerian Language and Home Economics.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Urban and Regional Planning (URP) department.
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Science Laboratory Technology (SLT) department.
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Nigerian Tertiary Institutions Offering Metallurgical and Material Engineering Course