If you are planning to study Prosthesis and Orthopaedic Technology at Federal University, Birnin Kebbi located in Kebbi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. FUBK was established in 2013 by the Federal Government of Nigeria to expand access to university education and promote academic excellence, research, and innovation in northwestern Nigeria. This page explains everything you need to know to increase your chances of gaining admission into FUBK.
Does Federal University, Birnin Kebbi (FUBK) offer Prosthesis and Orthopaedic Technology?
No, Federal University, Birnin Kebbi does not offer Prosthesis and Orthopaedic Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Federal University, Birnin Kebbi (FUBK) below to check if the Prosthesis and Orthopaedic Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Prosthesis and Orthopaedic Technology When Accredited in Federal University, Birnin Kebbi (FUBK)
O’Level Requirements
To study this course, candidates seeking admission into the Prosthesis and Orthopaedic Technology department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
FUBK Cut-Off Mark for Prosthesis and Orthopaedic Technology
The general UTME cut-off mark is 180, but due to the variation of Prosthesis and Orthopaedic Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUBK Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUBK Science Courses with their Requirements
1. Chemistry
To study this course, candidates seeking admission into the Chemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
2. Statistics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Statistics department.
any other relevant subject.
3. Applied Geophysics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Applied Geophysics department.
4. Geology
To study this course, the minimum requirement for applicants seeking admission to the Geology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other relevant subject.
5. Building Technology (BT)
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
6. Quantity Surveying (QS)
To study this course, candidates seeking admission into the Quantity Surveying (QS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
7. Medicine and Surgery
To study this course, candidates seeking admission into the Medicine and Surgery department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Nigerian Tertiary Institutions Offering Prosthesis and Orthopaedic Technology Course