If you are planning to study Woodwork Technology Education at Federal University, Birnin Kebbi located in Kebbi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. FUBK was established in 2013 by the Federal Government of Nigeria to expand access to university education and promote academic excellence, research, and innovation in northwestern Nigeria. This page explains everything you need to know to increase your chances of gaining admission into FUBK.
Does Federal University, Birnin Kebbi (FUBK) offer Woodwork Technology Education?
No, Federal University, Birnin Kebbi does not offer Woodwork Technology Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Federal University, Birnin Kebbi (FUBK) below to check if the Woodwork Technology Education course under the Faculty of Education has been updated.
Admission Requirements for Woodwork Technology Education When Accredited in Federal University, Birnin Kebbi (FUBK)
O’Level Requirements
To study this course, candidates seeking admission into the Woodwork Technology Education department under Faculty of Education, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any one (1) of Biology / Agricultural Science, Physics, or Chemistry and
two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
FUBK Cut-Off Mark for Woodwork Technology Education
The general UTME cut-off mark is 180, but due to the variation of Woodwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUBK Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUBK Science Courses with their Requirements
1. Statistics
To study this course, candidates aspiring to gain admission into Statistics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other relevant subject.
2. Medicine and Surgery
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Medicine and Surgery department.
3. Industrial Chemistry
To study this course, the minimum requirement for applicants seeking admission to the Industrial Chemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science.
4. Applied Geophysics
To study this course, candidates aspiring to gain admission into Applied Geophysics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
5. Building Technology (BT)
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
6. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
7. Microbiology
To study this course, candidates aspiring to gain admission into Microbiology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Nigerian Tertiary Institutions Offering Woodwork Technology Education Course