If you are planning to study Building Technology Education at Federal University Ndufu Alike, Ikwo located in Ebonyi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. FUNAI was established in 2011 by the Federal Government of Nigeria as part of a nationwide initiative to establish new federal universities. The institution was created to broaden access to quality higher education and foster research and innovation. This page explains everything you need to know to increase your chances of gaining admission into FUNAI.
Does Federal University Ndufu Alike, Ikwo (FUNAI) offer Building Technology Education?
No, Federal University Ndufu Alike, Ikwo does not offer Building Technology Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Federal University Ndufu Alike, Ikwo (FUNAI) below to check if the Building Technology Education course under the Faculty of Education has been updated.
Admission Requirements for Building Technology Education When Accredited in Federal University Ndufu Alike, Ikwo (FUNAI)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology Education department under Faculty of Education.
any other Science subject.
FUNAI Cut-Off Mark for Building Technology Education
The general UTME cut-off mark is 180, but due to the variation of Building Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUNAI Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUNAI Science Courses with their Requirements
1. Architecture
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
2. Mechatronics Engineering
To study this course, candidates aspiring to gain admission into Mechatronics Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
3. Mathematics
To study this course, the minimum requirement for applicants seeking admission to the Mathematics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subjects.
4. Education and Physics
To study this course, candidates aspiring to gain admission into Education and Physics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
two (2) other Science subjects or NTC / NBC.
5. Surveying and Geoinformatics
To study this course, candidates seeking admission into the Surveying and Geoinformatics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
6. Geology
To study this course, candidates aspiring to gain admission into Geology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other relevant subject.
7. Mechanical Engineering
To study this course, candidates seeking admission into the Mechanical Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant Science subjects.
Nigerian Universities Offering Building Technology Education Course