If you are planning to study Industrial Technical Education at Federal University Ndufu Alike, Ikwo located in Ebonyi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. FUNAI was established in 2011 by the Federal Government of Nigeria as part of a nationwide initiative to establish new federal universities. The institution was created to broaden access to quality higher education and foster research and innovation. This page explains everything you need to know to increase your chances of gaining admission into FUNAI.
Does Federal University Ndufu Alike, Ikwo (FUNAI) offer Industrial Technical Education?
No, Federal University Ndufu Alike, Ikwo does not offer Industrial Technical Education under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Federal University Ndufu Alike, Ikwo (FUNAI) below to check if the Industrial Technical Education course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Industrial Technical Education When Accredited in Federal University Ndufu Alike, Ikwo (FUNAI)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Industrial Technical Education department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Mathematics / Physics and
any other three (3) relevant subjects.
FUNAI Cut-Off Mark for Industrial Technical Education
The general UTME cut-off mark is 180, but due to the variation of Industrial Technical Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUNAI Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUNAI Science Courses with their Requirements
1. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
2. Petroleum Engineering
To study this course, candidates seeking admission into the Petroleum Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
3. Surveying and Geoinformatics
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
4. Education and Physics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Education and Physics department.
two (2) other Science subjects or NTC / NBC.
5. Geology and Geophysics
To study this course, candidates seeking admission into the Geology and Geophysics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
6. Zoology
To study this course, the minimum requirement for applicants seeking admission to the Zoology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
two (2) other Science subject.
7. Physics
To study this course, candidates aspiring to gain admission into Physics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Chemistry, Mathematics and
any other Science subject from
Biology / Agricultural Science.
Nigerian Tertiary Institutions Offering Industrial Technical Education Course