If you are planning to study Mechanical Engineering Technology at Federal University Ndufu Alike, Ikwo located in Ebonyi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUNAI.
Does Federal University Ndufu Alike, Ikwo (FUNAI) offer Mechanical Engineering Technology?
No, Federal University Ndufu Alike, Ikwo does not offer Mechanical Engineering Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Federal University Ndufu Alike, Ikwo (FUNAI) below to check if the Mechanical Engineering Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechanical Engineering Technology When Accredited in Federal University Ndufu Alike, Ikwo (FUNAI)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering Technology department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
JAMB Subject Combination
Physics/Technical Drawing.
FUNAI Cut-Off Mark for Mechanical Engineering Technology
The general UTME cut-off mark is 180, but due to the variation of Mechanical Engineering Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUNAI Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUNAI Science Courses with their Requirements
1. Agriculture
To study this course, candidates seeking admission into the Agriculture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science,
Mathematics / Physics, and
2. Physical and Health Education
To study this course, candidates aspiring to gain admission into Physical and Health Education department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology or its equivalent
and any two (2) other relevant subjects.
3. Microbiology
To study this course, candidates seeking admission into the Microbiology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
4. Surveying and Geoinformatics
To study this course, candidates seeking admission into the Surveying and Geoinformatics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
5. Geology and Geophysics
To study this course, candidates aspiring to gain admission into Geology and Geophysics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
6. Physiotherapy
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Physiotherapy department.
7. Quantity Surveying (QS)
To study this course, the minimum requirement for applicants seeking admission to the Quantity Surveying (QS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
Nigerian Tertiary Institutions Offering Mechanical Engineering Technology Course