If you are planning to study Textile Science and Technology at Federal University Ndufu Alike, Ikwo located in Ebonyi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. FUNAI was established in 2011 by the Federal Government of Nigeria as part of a nationwide initiative to establish new federal universities. The institution was created to broaden access to quality higher education and foster research and innovation. This page explains everything you need to know to increase your chances of gaining admission into FUNAI.
Does Federal University Ndufu Alike, Ikwo (FUNAI) offer Textile Science and Technology?
No, Federal University Ndufu Alike, Ikwo does not offer Textile Science and Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Federal University Ndufu Alike, Ikwo (FUNAI) below to check if the Textile Science and Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Textile Science and Technology When Accredited in Federal University Ndufu Alike, Ikwo (FUNAI)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Textile Science and Technology department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
FUNAI Cut-Off Mark for Textile Science and Technology
The general UTME cut-off mark is 180, but due to the variation of Textile Science and Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUNAI Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUNAI Science Courses with their Requirements
1. Microbiology
To study this course, the minimum requirement for applicants seeking admission to the Microbiology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
2. Computer Science (CS)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Science (CS) department.
any two (2) other Science subjects.
3. Architecture
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
4. Botany
To study this course, the minimum requirement for applicants seeking admission to the Botany department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
5. Zoology
To study this course, candidates aspiring to gain admission into Zoology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
two (2) other Science subject.
6. Geography
To study this course, the minimum requirement for applicants seeking admission to the Geography department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other two (2) Science subjects.
7. Surveying and Geoinformatics
To study this course, candidates seeking admission into the Surveying and Geoinformatics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Nigerian Tertiary Institutions Offering Textile Science and Technology Course