If you are planning to study Industrial Chemistry and Chemical Entrepreneurship at Federal University of Technology Akure located in Ondo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. FUTA was established in 1981 by the Federal Government of Nigeria as a university of technology. It was founded to promote technological advancement, scientific research, and the training of highly skilled professionals. This page explains everything you need to know to increase your chances of gaining admission into FUTA.
Does Federal University of Technology Akure (FUTA) offer Industrial Chemistry and Chemical Entrepreneurship?
No, Federal University of Technology Akure does not offer Industrial Chemistry and Chemical Entrepreneurship under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology Akure (FUTA) below to check if the Industrial Chemistry and Chemical Entrepreneurship course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Industrial Chemistry and Chemical Entrepreneurship When Accredited in Federal University of Technology Akure (FUTA)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Industrial Chemistry and Chemical Entrepreneurship department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) science subjects.
JAMB Subject Combination
any two (2) science subjects.
FUTA Cut-Off Mark for Industrial Chemistry and Chemical Entrepreneurship
The general UTME cut-off mark is 180, but due to the variation of Industrial Chemistry and Chemical Entrepreneurship cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTA Science Courses with their Requirements
1. Forestry and Wood Technology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Forestry and Wood Technology department.
Biology / Agricultural Science,
at least ‘O’ Level pass in Physics.
2. Architecture
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
3. Microbiology
To study this course, candidates seeking admission into the Microbiology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
4. Industrial and Production Engineering
To study this course, the minimum requirement for applicants seeking admission to the Industrial and Production Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
5. Applied Geology
To study this course, candidates aspiring to gain admission into Applied Geology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
6. Statistics
To study this course, the minimum requirement for applicants seeking admission to the Statistics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other relevant subject.
7. Quantity Surveying (QS)
To study this course, candidates seeking admission into the Quantity Surveying (QS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
Nigerian Tertiary Institutions Offering Industrial Chemistry and Chemical Entrepreneurship Course