If you are planning to study Physics with Computational Modeling at Federal University of Technology Akure located in Ondo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. FUTA was established in 1981 by the Federal Government of Nigeria as a university of technology. It was founded to promote technological advancement, scientific research, and the training of highly skilled professionals. This page explains everything you need to know to increase your chances of gaining admission into FUTA.
Does Federal University of Technology Akure (FUTA) offer Physics with Computational Modeling?
No, Federal University of Technology Akure does not offer Physics with Computational Modeling under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology Akure (FUTA) below to check if the Physics with Computational Modeling course under the Faculty of Science has been updated.
Admission Requirements for Physics with Computational Modeling When Accredited in Federal University of Technology Akure (FUTA)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Physics with Computational Modeling department under Faculty of Science, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Chemistry, Mathematics and
any other Science subject from:
Biology or Agricultural Science.
FUTA Cut-Off Mark for Physics with Computational Modeling
The general UTME cut-off mark is 180, but due to the variation of Physics with Computational Modeling cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTA Science Courses with their Requirements
1. Marine Science and Technology
To study this course, candidates seeking admission into the Marine Science and Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subject.
2. Information Technology
To study this course, the minimum requirement for applicants seeking admission to the Information Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subjects.
3. Civil Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Civil Engineering department.
4. Building
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
5. Software Engineering
To study this course, candidates seeking admission into the Software Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects.
6. Cyber Security
To study this course, candidates aspiring to gain admission into Cyber Security department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
two (2) other Science subjects.
7. Agricultural Engineering (AE)
To study this course, candidates aspiring to gain admission into Agricultural Engineering (AE) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any one other subject from:
Introduction to Agricultural Science,
Materials and Workshop Process and Machining,
Tractor Layout Power Unit Under Carriage and Auto Electricity;
Transmission System;
Implement and Machine;
Principles of Crop Husbandry and Land Use,
Materials and Workshop Processes;
Construction and Maintenance of Agricultural Machines;
General Metal Work;
General Wood Work and Building / Engineering Drawing.
Nigerian Tertiary Institutions Offering Physics with Computational Modeling Course