If you are planning to study Technology and Vocational Education at Federal University of Technology Akure located in Ondo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUTA.
Does Federal University of Technology Akure (FUTA) offer Technology and Vocational Education?
No, Federal University of Technology Akure does not offer Technology and Vocational Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology Akure (FUTA) below to check if the Technology and Vocational Education course under the Faculty of Education has been updated.
Admission Requirements for Technology and Vocational Education When Accredited in Federal University of Technology Akure (FUTA)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Technology and Vocational Education department under Faculty of Education, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any three (3) other relevant subjects.
FUTA Cut-Off Mark for Technology and Vocational Education
The general UTME cut-off mark is 180, but due to the variation of Technology and Vocational Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTA Science Courses with their Requirements
Biotechnology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Biotechnology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Computer Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Remote Sensing and Geosciences Information System
SSCE Requirements
To study this course, candidates aspiring to gain admission into Remote Sensing and Geosciences Information System department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Joinery,
Floors and Ceiling Finishing, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
Crop, Soil and Pest Management
SSCE Requirements
To study this course, candidates seeking admission into the Crop, Soil and Pest Management department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science,
one Science/Social Science subject and
at least ‘O’ Level pass in Physics.
Building
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Architecture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Mathematics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mathematics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subjects.
Nigerian Tertiary Institutions Offering Technology and Vocational Education Course