If you are planning to study Environmental Science and Technology at Federal University of Technology Minna located in Niger State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUTMINNA.
Does Federal University of Technology Minna (FUTMINNA) offer Environmental Science and Technology?
No, Federal University of Technology Minna does not offer Environmental Science and Technology under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology Minna (FUTMINNA) below to check if the Environmental Science and Technology course under the Faculty of Science has been updated.
Admission Requirements for Environmental Science and Technology When Accredited in Federal University of Technology Minna (FUTMINNA)
O’Level Requirements
To study this course, candidates seeking admission into the Environmental Science and Technology department under Faculty of Science, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subject.
FUTMINNA Cut-Off Mark for Environmental Science and Technology
The general UTME cut-off mark is 180, but due to the variation of Environmental Science and Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTMINNA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTMINNA Science Courses with their Requirements
Information Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Information Technology department.
any two (2) other relevant subjects.
Applied Geophysics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Applied Geophysics department.
Food Science and Technology (FT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Food Science and Technology (FT) department.
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Architecture
SSCE Requirements
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Electrical and Computer Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Electrical and Computer Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any one other relevant subject.
Education and Physics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Education and Physics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
two (2) other Science subjects or NTC / NBC.
Agricultural and Bioresources Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Agricultural and Bioresources Engineering department.
Introduction to Agricultural Science, Materials and Workshop Process and Machining, Tractor Layout Power Unit Under Carriage and Auto Electricity; Transmission System; Implement and Machine;
Principles of Crop Husbandry and Land Use, Materials and Workshop Processes; Construction and Maintenance of Agricultural Machines; General Metal Work; General Wood Work and Building / Engineering Drawing.
Nigerian Tertiary Institutions Offering Environmental Science and Technology Course